Thermo King Genset Manual

14.07.2018admin0 Comments
Thermo King Genset Manual Rating: 9,6/10 4334reviews

how to download linux on mac

Generator Set Range SG-3000 & SG-4000. Thermo King has set the world standard in marine container. As with all Thermo King products, the SG Marine Genset range. TRUCK: DIESEL POWERED. Download the PDF version of the install manual for your truck unit from the list below. Installation (3).

Thermo King Genset Parts Manual For Sgco 3000Thermo King Genset Parts Manual For Sgco 3000

The C201 should make a great genset engine. I probably rebuilt close to 50 of those engines back when I used to work on Thermo Kings. I always liked the C201's better than the later DI engines. I remember seeing many C201's going over 30,000 hours before overhauls. If I remember right (15 yrs.) the bellhousing was about the size of a SAE #5, and the flywheels had 5 or 6 steel drive pins which were pressed in. The compressor coupler had hard rubber insert bushings which were driven by the flywheel pins, and was about a 1' tapered keyed shaft drive. The C201 should make a great genset engine.

I probably rebuilt close to 50 of those engines back when I used to work on Thermo Kings. I always liked the C201's better than the later DI engines. I remember seeing many C201's going over 30,000 hours before overhauls. If I remember right (15 yrs.) the bellhousing was about the size of a SAE #5, and the flywheels had 5 or 6 steel drive pins which were pressed in.

The compressor coupler had hard rubber insert bushings which were driven by the flywheel pins, and was about a 1' tapered keyed shaft drive.i believe the ones i posted above are 201's--how to best identify?? Well it seems that I have run into a problem, not sure which way it will go. The bell housing on the 201 is fine. It is a standard SAE #6 with the two bottom holes not drilled, that is easy to cure. The measurements are fine. But the flywheel is special for the mounting of the compressor. Yamaha Yfz 450 Quad 2010 Workshop Manual.

It uses pressed in pins in the flywheel that drive a flex plate with grommets in it. There are also tapped holes but they are not in a diameter of a standard SAE flywheel. They are somewhat over 10 inches in diameter, eight holes tapped 5/16. Larger than a #7 1/2 but smaller than a #8.

I may have to come up with a flywheel from a vehicle unit, maybe the Luv truck, not sure. Tech at Magnatron has the information been waiting for two days for their answer. I am installing a 21 kw gen end. I don't want to be limited by the generator and if needed the 201 can be turned up some, maybe a turbo and a bit bigger injectors. I don't think that my use will be too much for the 201 as it is, but don't want to be limited by the generator. I will be using a 4 pole dedicated 120/240 single phase.

My use is a shop trailer with the heaviest comsumpsion from a Airco 300 amp heliarc welder. It runs fine on a 50 amp breaker. It will also charge Surrite batteries. The trailer will be totally self contained with solar panels and its own water supply, 700 gallons. The water system, plumbing, electrical wiring is all in now along with the equipment, but not the solar panels and inverter unit yet. I currently run a Freightliner Condo with deep cycle batteries, inverter, generator and everything but the kitchen sink, so I have some current experience with the systems. See even an ice maker and freezer.

The trailer is a 53/102 reefer unit and will have living quarters in it also, will be in it a lot. I would be interested in info that anyone has on the flywheel situation or other factors involved. The governor seems great, it is set at 1800 now and is staying in its original location. Trailer will look like a totally stock reefer.

• Page 2 and 3: • Page 5 and 6: • Page 7 and 8: • Page 9 and 10: • Page 11 and 12: • Page 13 and 14: • Page 15 and 16: • Page 17 and 18: • Page 19 and 20: • Page 21 and 22: • Page 23 and 24: • Page 25 and 26: • Page 27 and 28: • Page 29 and 30: • Page 31 and 32: • Page 33 and 34: • Page 35 and 36: • Page 37 and 38: • Page 39 and 40: • Page 41 and 42: • Page 43 and 44: • Page 45 and 46: • Page 47 and 48: • Page 49 and 50: • Page 51 and 52: • Page 53 and 54: Operating Instructions Digital Outp • Page 55 and 56: Operating Instructions Alarm List M • Page 57 and 58: Operating Instructions 108. ENGINE • Page 59 and 60: Operating Instructions Message List • Page 61 and 62: Operating Instructions 125.